15 Strands 15ft Crystal Beaded Ceiling Drape Curtains and Hanging Kit

[About] Quantity: 1 Set of Ceiling Drape Material: Metal, Acrylic What you get: 15x Strands of Iridescent Beads (preset on 2x Rods) 4x Rods 8x Ceiling Hook Mounts 8x Sets of Steel Brackets 8x Sets of Screws Overall Size: 15ft L x 20″ W Each Bead Strand Length: 14.8ft Bead Size: 1cm (Diameter) x 1mm (Thickness) Bead Color: Iridescent Each Rod Size: 20″L x 0.5″W [Information] Additional Information: 2x of the Rods are already installed along with the beads, the other 2x rods are not attached. Item comes with a Bag of Parts needed to hang item. Bag contains the following: 8x Sets of Steel Brackets: Each Steel Bracket is pre-installed with 2x Washers, 2x Nuts, 2x Screws, 2x Stoppers. Steel Brackets are attached to a beam that will help support the item. Each of this set will use 1x Set of Screws so it can be screwed down on to the beam support 8x Sets of Screws: Each Set is individually wrapped with 2x Screws, 2x Plastic Anchors These Screws go into the small oval holes of the Steel Brackets into the supporting beam to mount the item Each Rod contains 2x Triangular Hangers on each end to slide the Ceiling Hook Mount through. Triangular Hanger Size: 0.5″L x 0.5″W Ceiling Hook Mount Size: 4″ Diameter x 0.75″ Thick Ceiling Hook: 1.25″L x 1″W Individual Parts Measurement: SET of Steel Bracket: Contains: 2x Large Ovals, 2x Small Ovals, and Center Hole Steel Bracket: 3.5″L x 0.75″W x 1mm (Thickness) Washer Outer/Inner Diameter: 0.5″, 0.5cm Nut: 1cm Length x 4mm Inner Diameter Screw: 0.75″L x 1cm W x 0.5cm Neck Diameter Stopper: 0.25″ L x 1cm Diameter SET of Screw: Screw: 1″L x 0.25″ W x 4mm Neck Diameter Plastic Anchor: 1″L x 1cm W x 0.5cm Each Set is individually wrapped How to Install: You will need to find/create 2x Parallel Support Beams with enough space between each other to assemble this item Take 1x Set of Steel Bracket and remove the Stoppers. Take 1x Set of Screws. Take Steel Bracket and place on preferred area on Support Beam with bottom tip of screws facing you. Take a Screw and insert into opening of Plastic Anchor from Screw Set. Proceed to drill into one of the small ovals on the Steel Bracket into the Support Beam. Repeat this step for the remaining Plastic Anchor and Screw. Take 1x Ceiling Hook Mount and align its 2 holes so that the Screws from the Steel Bracket can go through it. Proceed to take the 2x Stoppers removed from the Steel Bracket and screw on each Screw Tip to secure the Ceiling Hook Mount. Repeat Steps 2 + 3 assemble another Hook Mount across the one you just setup (ALLOW ENOUGH SPACE for attaching the rods) Take one of the Preset Rod w/Beads. Each end of the Rod has a Triangular Hole to slide into the Ceiling Hook Mount. Slide each Triangular Hole on the Rod into each Ceiling Hook Mount. Repeat the Previous Steps to Hook the other Preset Rod w/Beads. At this time, you can choose how far or close you’d like the other end of the Ceiling Drape to be. This creates a wide or narrow Drape Effect based on preference. OPTIONAL: You can create more Drape Effects of varying size if you choose to use 1x or 2x of the remaining Rods. If you’d like to proceed with this option: 8-1. Repeat the previous Steps for installing the Ceiling Hook Mounts for however many rods you choose to use. The only thing different is when you are applying the Drape effect with the remaining rods, you are pushing each rod against the beads as you attach it to the Ceiling Hook Mounts. Once the rod is attached, align the bead strands by following the alignment of the Preset Rod. 8-2. Once the bead strands are aligned, pull each strand of beads in the direction of your preference to help shape the size of the Drape Effect.